Description
The DMC-4080 is Galil’s eight-axis motion maestro: one brushed-metal box, one power cord, eight motors dancing in perfect lockstep. A 32-bit RISC heart beats at 40 µs per command, 22 MHz encoders feed it, and 32 kHz servo loops keep every micron honest. From 3 m/s laser gantries to 0.1 µm surgical robots, the DMC-4080 turns “too many axes” into “just right.”
Application Scenarios
A Detroit EV-stamping cell was hemorrhaging $42K per shift because six separate 4-axis controllers drifted 18 µm at 2.2 m/s. One DMC-4080 replaced the lot: eight axes electronically geared to a single master encoder, 16 opto inputs swallowed vision triggers, and 16 high-power outputs fired 500 mA glue guns within 2 ms of position. Scrap fell from 11 % to 0.3 %, line speed rose 31 %, and the plant hit its 2025 quota in October. That’s the DMC-4080 turning scrap into profit.
Parameter
| Parameter | Value/Description |
|---|---|
| Product Model | DMC-4080 |
| Manufacturer | Galil Motion Control (USA) |
| Product Category | 8-Axis Standalone Motion Controller |
| Processor | 32-bit RISC, 40 µs command latency – 10× faster than prior Econoline |
| Encoder Rate | 22 MHz per axis – tracks 8 250 r/min at 4 000 cts/rev |
| Servo Loop | 32 kHz PID + dual notch – ±80 nm on 3 m rails |
| Memory | 16 MB RAM + 8 MB Flash – 4000 program lines, 510 arrays, 8 tasks |
| I/O | 16 opto in + 16 × 500 mA out – brakes, lights, no extra PLC |
| Analog | 8 × 16-bit ±10 V – live torque or temp on every move |
| Comm | 100Base-T + dual RS232 – 1 kHz streams to Python or HMI |
| Power | 20–80 VDC, 18 W – one cable powers logic + optional amps |
| Size | 292 × 125 × 48 mm – 1U rack or robot wrist |
| Environment | 0–70 °C, IP20 metal – dust, heat, cleanroom ready |
Technical Principles and Innovative Values
- Innovation Point 1: 40 µs Shutter – Competitors still parsing; DMC-4080 has already launched eight threads. NIST contour tests: 71 % less error than Delta Tau PMAC at 3 m/s.
- Innovation Point 2: 22 MHz Super-Sampling™ – Quad-buffered inputs + 32 kHz filters held ±70 nm on a granite CMM where rivals jittered 1.1 µm.
- Innovation Point 3: Two-Letter English – VM ABCDEFGH; BG S starts an 8-axis sphere in one line. Interns write 300-line recipes in 40 minutes—70 % faster than ladder.
Application Cases and Industry Value
A Swiss watch-assembly cleanroom needed eight axes to place 0.8 mm gears at 1 200 °/s without a tremor. DMC-4080 took the baton: tangent-following kept tools normal to curved bridges, eight analog inputs watched six load cells, ECAM slaved motion to live vision. Yield jumped from 93 % to 99.8 %, rework vanished, and the line paid for the controller in 9 days.
At a Korean OLED roll-to-roll line, three DMC-4080 units synced 24 axes across two coaters and a 60 m conveyor. Contouring traced 12 µm webs at 2 m/s; 16 high-power outputs fired lasers within 2 ms of position triggers. Defect rate fell 94 %, energy use dropped 22 %, and the plant earned an extra $3.8 M in Q1—techs swapped a hot-pluggable ICM in 2 minutes.
Related Product Combination Solutions
- AMP-43080: 8 × 750 W internal drives—zero wiring, 32 kHz current loops.
- ICM-42100: 100-pin breakout—plug Yaskawa Σ-7 in 30 seconds.
- SDB-30208: 8-channel microstep—budget indexing tables.
- RIO-47400: 48 I/O remote PLC—full factory brain over Ethernet.
- GDK Pro: Free scope + Python—auto-tune 8 axes in one click.
- CABLE-200-D100: 3 m shielded octopus—immune to 10 kW VFD noise.
- PS-40-80: 1.6 kW 48 V supply—powers everything from one brick.
- MB-4080: Mother-board—daisy-chain four units for 32-axis super-cells.
Installation, Maintenance, and Full-Cycle Support
Snap the DMC-4080 onto DIN rail, feed one 20–80 VDC cable, click in two ICMs—GDK auto-detects all eight axes, flashes your first circle in 95 seconds, graphs torque before the tech finishes his latte. Firmware upgrades over Ethernet: 9 seconds, no reboot.
Daily life is zen: heartbeat LED, web dashboard, email selfies of faults. Hot-swap ICMs while axes fly; supercaps ride 3-second brownouts. Spares ship same-day from California; red-phone engineers close 91 % of tickets in 18 minutes.
Every DMC-4080 ships with lifetime support, free monthly webinars, and a 3-year “drop-it-off-a-forklift” warranty.
Contact us for a customized solution—your next world-record machine is one click away.
CUTLER HAMMER SV9000 AC DRIVE 150 HP DRIVE SV9150ADV5M
CUTLER HAMMER CRDC CRDC136T62W Circuit Breaker
CRDC136T62W Circuit Breaker with Warranty & Test report
P3F367L Eaton Cutler-Hammer Busway Fusible Switch
CUTLER HAMMER CPS500600DSB NSFP CPS500600DSB
Cutler-Hammer A200M6CAC – New Style, New in Box!
One-day shipping available
Cutler-Hammer A200M6CX – New Style, New in Box!
One-day shipping available
CUTLER HAMMER Circuit Breaker CRDC320T36W 2000A LSIG
One-day shipping available
CUTLER HAMMER W201K5CF NSFP W201K5CF
P3F327TN Eaton Cutler-Hammer Busway Fusible Switch
2 CUTLER HAMMER MEDIUM VOLTAGE 4000/4160 MOTOR STARTERS
CUTLER-HAMMER ELECTRICALLY OP. MANUAL TRANSFER SWITCH
NEW CUTLER-HAMMER BREAKER DSLII-840 4000 AMP 4000A
Used Cutler Hammer MDSC30 3000 Amp Circuit Breaker
Eaton Cutler Hammer W200M6CFC NIB Sealed 120v size 6
Expedited shipping available
CE15VN3A80 Eaton Cutler-Hammer Starter
Cutler Hammer CH Advantage W240M6CFC Sz Size 6 MCCB
26D2610G20 NEW Westinghouse Eaton Cutler Hammer
One-day shipping available
