- Model: MVI46-MNET
- Brand: ProSoft Technology
- Series: SLC 500 Platform
- Core Function: Connects Allen-Bradley SLC 500 processors to Modbus TCP/IP networks via Ethernet
- Type: Modbus TCP/IP Communication Module
- Key Specs: 10/100 Mbps Ethernet, Client/Server support, 1-slot width
- Condition: New Original (New Surplus), not refurbished
Product Introduction
The ProSoft MVI46-MNET serves as the primary gateway for integrating modern Modbus TCP/IP devices into legacy Allen-Bradley SLC 500 architectures. By occupying a single slot in the 1746 chassis, it enables the SLC processor to exchange data with power meters, VFDs, and secondary HMI systems over standard Ethernet infrastructure.
In aging infrastructure environments, the MVI46-MNET is often the critical link that prevents a full rip-and-replace of the control system. It offloads the protocol encapsulation from the SLC CPU, maintaining system scan times while managing up to 100 client commands for complex data harvesting from distributed Modbus nodes.
Key Selling Points & Differentiators
- Simultaneous Client/Server: Operates as both a Modbus TCP/IP Client (Master) and Server (Slave) simultaneously, allowing bidirectional data flow between the SLC and the plant network.
- Large Database Capacity: Features a 5,000-word internal database, sufficient for high-density I/O mapping without straining backplane bandwidth.
- Tested Under Load: Every unit is stress-tested on a 1746-A10 rack for 24 hours to verify heat dissipation and Ethernet port stability.
- Not Recommended For: Deterministic high-speed motion synchronization; Ethernet latency over Modbus TCP is typically unsuitable for <20 ms loop requirements.
- Compatibility: Fully compatible with 1746-L531, L532, L541, L542, and L551 processors.
Quality Transparency Strategy (QC SOP)
- Incoming Inspection: Traceability is verified via serial number cross-referencing; we inspect for PCB warping or signs of “capacitor dry-out” common in long-term shelf storage.
- Live Functional Test: Modules are mounted in an SLC rack. We perform a ping test and establish a Modbus TCP session using a Modbus scanner tool to verify the RJ45 port physical layer and stack.
- Electrical Parameter Tests: We perform a ground continuity check and verify the 800 mA current draw to ensure the unit stays within the 1746 power supply specifications.
- Firmware Verification: Firmware version (e.g., v2.03) is documented. We can flash specific revisions upon request to match your existing logic “G-File” configuration.
- Final QC + Packaging: Unit is ESD-bagged and boxed in high-impact foam to survive international air freight transit.
Gnubi EPX200 Quad DS1 TXCVR
Gnubi EPX16 with CPU AND 4 EPX200,
JDS MTA100 Attenuator mainframe W/8 1×4 Cassets
Tektronix P6217 4 GHz Active Probe
Agilent 70004 / 70820A Microwave Transition
HP 81000KA, Bare Fiber Adapter. 125 um, threaded
HP 81050BL, Bare Fiber Adapter. 125 um, threaded
OMEGA 5TC-TT-J-30-72 Insulated Thermocouples 5 CABLES
Sumitomo SDT8802-RC-QN 622Mbps reciver molded
Hp 16717A 333 MHz State/2 GHz Timing Zoom Logic Analyze
Newport 8016 Modular Controller w 16 ModuLes
Newport 9016 / 8605.8C Modular Controller w 6 ModuLes
Newport 8325D Dual 15W Temperature Control Module
Newport 8510 LDD Temperature Control Module
Newport 6505Temperature Control Module
DiCon GP700 Programmable Fiber Multi Switch 1×32,2x1x4
EXFO IQ-206 / IQ-2400 w 6 ModuLes
EXFO IQ-206 / IQ-3100 w 2 ModuLes
FlashLink Model FL-101A
Tektronix P6026B 1X-10X
