Product Core Brief

• Model: PR6423/003-131 + CON041
• Brand: EPRO (Emerson)
• Series: MMS 6000 / MMS 3000
• Core Function: High-stability non-contact measurement with isolated signal conversion.
• Product Type: Sensor + Isolated Signal Converter Kit
• Key Specs: 8mm Tip | 4.0m Integrated Cable | Galvanic Isolation
• Condition: New Original (New Surplus)

 

Product Introduction

The PR6423/003-131 + CON041 is a specialized eddy current measurement chain designed for industrial environments where electrical noise and ground loops are a significant concern. This kit pairs the 003-series sensor, featuring enhanced temperature compensation and a 4.0 m integrated cable, with the CON041 signal converter. The defining feature of the CON041 is its built-in galvanic isolation, which protects the signal integrity by breaking ground loops between the machine-side sensor and the rack-side monitoring system.

This system is commonly used for radial shaft vibration and axial position monitoring on large turbomachinery. The PR6423/003-131 + CON041 excels in applications where the sensor and the monitoring rack are at different ground potentials, a common scenario in older plants or complex facilities. By providing a clean, isolated 0 to -20 V DC signal, it ensures that the vibration data reaching the DCS or MMS 6000 rack is free from common-mode interference.

 

Frequently Asked Questions

Q: What is the primary advantage of the CON041 over the standard CON011? A: Honestly, it’s all about the isolation. In many large plants, the ground at the turbine is not the same as the ground in the control room. Using a standard converter can lead to “noise” that looks like vibration. The CON041 uses galvanic isolation to block that interference, making it a lifesaver for troubleshooting “ghost” alarms.

Q: Does this 4.0 m cable require an extension to reach 5.0 m? A: That depends on the converter’s calibration. The PR6423/003-131 has a 4.0 m integrated lead. If the CON041 is calibrated for a 5.0 m system, you must use a 1.0 m extension. Most common mistake? Adding a 5.0 m extension to a 4.0 m sensor and expecting the 8.0 V/mm sensitivity to remain accurate. It won’t.

Q: Can I use this system for safety-instrumented functions (SIL)? A: Yes, these components are frequently used in SIL-rated turbine protection systems. However, ensure your loop calculation accounts for the specific response times and failure modes of the isolated converter.

Q: Is the CON041 compatible with 4-20 mA inputs? A: Not directly. The CON041 provides a buffered voltage output (0 to -20 V DC). If you need a current loop, you should look at the CON021 or add a separate voltage-to-current isolator.

Q: How do you handle warranty for “New Surplus” items like this? A: We treat these as mission-critical spares. While they are surplus, we provide a full functional guarantee. We bench-test the PR6423/003-131 + CON041 as a pair to ensure the isolation circuit is intact and the voltage slope is within OEM specs before it ships.

FOXBORO F6501A-A CONVERTER

GE TS-6631 170M57D7 CRANE CONTACTOR

FIKE903 617016-01 MODULE

FIKE903 9182.434 MODULE

ROSEMOUNT 623785 MICROPROCESSOR BOARD

POWER CIRCUITS FSC4C CONTROLLER

FOXBORO 873 PH/ORP ANALYZER

FOXBORO DM400YL FBM10 120VAC INPUT/OUTPUT MODULE

FOREMOST PEF-II PELLET FEEDER

FOXBORO I/A P0901VK 80MB HARD DRIVE W/ AP20

FOXBORO I/A P0901VK 80MB HARD DRIVE AP20 S/W

FOXBORO I/A P0400VT AP20 APPLICATIONS PROCESSOR 20

FOXBORO 7925050IC MODULE

FOXBORO I/A P0400ZG NODE BUS INTERFACE (NBI)

FOXBORO I/A P0400QK PER TAPE W/CONT

FOXBORO F6501A-A RS485-RS232 Converter

FOXBORO P0960GC WP30 WORKSTATION PROCESSOR 30

ABB SOLID STATE TRIP TYPE SS SS5G

AB ALLEN-BRADLEY SLC150 1745-LP153 PROCESSOR UNIT