Product Core Brief
- Model: PR6423/004-010
- Brand: EPRO (Emerson)
- Series: MMS 3000 / MMS 6000
- Core Function: High-precision measurement of shaft vibration and position.
- Product Type: Eddy Current Displacement Sensor
- Key Specs: 8mm Sensor Tip | 1.0m Integrated Cable | M10x1 Thread
- Condition: New Original (New Surplus)
Product Introduction
The PR6423/004-010 is an eddy current displacement sensor designed for critical machinery protection and monitoring. It provides non-contact measurement of radial shaft vibration, axial position, and eccentricity in high-speed rotating equipment. This specific variant features a 1.0 m integrated cable, typically used when the signal converter or junction box is mounted in close proximity to the measurement point on the machine casing.
As part of the Emerson EPRO 004-series, the PR6423/004-010 is engineered for high reliability in harsh industrial environments. Its inductive principle ensures that measurement accuracy is unaffected by the presence of non-conductive lubricants or steam in the air gap. The unit is fully compatible with the MMS 6000 and MMS 3000 monitoring systems, provided the total system cable length is correctly matched to the converter calibration.
Frequently Asked Questions
Q: Why is the cable only 1.0 m long on this version? A: The PR6423/004-010 is designed for specific mounting configurations where the terminal box is attached directly to the machine housing. Honestly, the shorter cable is an advantage in high-vibration areas because it minimizes the amount of unsupported cable that can “whip” and cause fatigue at the sensor head.
Q: Can I extend this 1.0 m cable to 5.0 m? A: Yes, but you must use a specific EPRO extension cable. The most common mistake is using a generic coaxial cable. To maintain the 8.0 V/mm sensitivity, the total electrical length (sensor cable + extension) must match the requirements of your CON series signal converter (usually 5.0 m or 10.0 m).
Q: Is this sensor suitable for high-temperature turbine environments? A: Absolutely. The sensor head is rated for operation up to +180°C. In our experience, the 004-series handles thermal cycling very well, showing minimal “zero-shift” compared to lower-grade sensors.
Q: Can I swap a 002-series sensor for this 004-series unit? A: Generally, yes, if the mechanical specs (8mm tip, M10 thread) match. However, always verify the firmware and calibration settings in your MMS 6000 rack. The 004-series often has tighter manufacturing tolerances, which might require a minor gapping adjustment during commissioning.
Q: How do you verify these are not used pulls? A: We perform a strict visual and electrical audit. We look for “witness marks” on the M10 threads and any discoloration on the PEEK tip. Every PR6423/004-010 we stock as New Surplus is tested for core-to-shield insulation resistance to ensure it hasn’t been compromised by moisture or previous handling.
National Instruments VXI-TB-196
Modicon PC-0984-485 Programmable Controller
Adept 01182-000 Dual C Amp Board
Adept Technology 10332-00505 R EJI Board
Adept Technology 10332-00800 DIO Board
Adept 10350-01044 AWCII Board
Adept Technology 10338-53105 Dual C Amp Board
BERB XW-15 Cylindrical Roller Bearing
9 IBM 39V2208 Hy Toner Cartridge Cyan
8 IBM 39V2209 hy Toner Cartridge Magenta
8 IBM 39V2211 Hy Toner Cartridge Black
6 IBM 39V2211 Hy Toner Cartridge Black
9 IBM 39VB2209 Hy Toner Cartridge Magenta
9 IBM 39V2210 Hy Toner Cartridge Yellow
5 IBM 39V2210 High Toner Cartridge Yellow
9 IBM 39V2214 Toner Cartidge Yellow
Mircostep Drive S Series Compumotor
Direct Koyo D2-09BDC1-1 PLC Complete
Direct LOGIC DP-M321 DPM321 Panel Controller
BECKER VTC6/2 D71A4P VACUUM PUMP
