Product Core Brief
- Model: RS-FS-9001 362A1052P004
- Brand: GE (General Electric) / Reuter Stokes
- Series: Flame Tracker
- Core Function: UV flame detector for gas turbine combustion monitoring
- Product Type: Flame Detector / Flame Sensor
- Key Specs: UV Detection | 4–20 mA Output | 24 VDC | <100 ms Response
- Condition: New Original / New Surplus
Key Technical Specifications
- Manufacturer: GE / Reuter Stokes
- Model Number: RS-FS-9001
- Part Number: 362A1052P004
- Product Type: UV Flame Detector (Flame Tracker)
- Detection Principle: Ultraviolet (UV) spectral sensing via silicon carbide (SiC) photodiode
- Output Signal: 4–20 mA analog current loop
- Operating Voltage: 24 VDC (nominal)
- Power Consumption: ≤5 W
- Response Time: <100 ms
- Operating Temperature: -20 °C to +70 °C
- Storage Temperature: -40 °C to +85 °C
- Protection Rating: IP54 / IP65 (installation-dependent)
- Mounting: Flange / threaded fitting
- Weight: Approximately 0.8–1.2 kg
Product Introduction
GE RS-FS-9001 362A1052P004 is a Flame Tracker ultraviolet flame detector manufactured by GE’s Reuter Stokes division. The unit monitors combustion flame presence in gas turbines, utility boilers, petrochemical heaters, and industrial furnaces. It uses a silicon carbide (SiC) UV photodiode to detect flame-generated ultraviolet radiation while rejecting visible light and infrared heat signatures from hot combustion chamber walls.
The detector outputs a 4–20 mA signal compatible with GE combustion management systems. Its response time of under 100 ms enables rapid flame-loss detection and automatic fuel shutoff before hazardous fuel accumulation occurs. The welded construction prevents unauthorized disassembly, and the dry design eliminates the need for external cooling water, reducing maintenance overhead in turbine installations.
Frequently Asked Questions (FAQ)
Q: Is the 362A1052P004 interchangeable with the 362A1052P404 or 362A1052P104?
A: Not without verification. These part numbers belong to the same RS-FS-9001 Flame Tracker family but may differ in sensor sensitivity range, output configuration, or mounting hardware. Always match the full part number — including the suffix — against your existing unit’s nameplate before ordering.
A: Not without verification. These part numbers belong to the same RS-FS-9001 Flame Tracker family but may differ in sensor sensitivity range, output configuration, or mounting hardware. Always match the full part number — including the suffix — against your existing unit’s nameplate before ordering.
Q: Will this detector work with my existing combustion management system?
A: The RS-FS-9001 outputs a standard 4–20 mA signal and operates on 24 VDC, which is compatible with most GE combustion management systems. However, you should confirm the signal scaling, alarm thresholds, and wiring pinout against your specific controller documentation.
A: The RS-FS-9001 outputs a standard 4–20 mA signal and operates on 24 VDC, which is compatible with most GE combustion management systems. However, you should confirm the signal scaling, alarm thresholds, and wiring pinout against your specific controller documentation.
Q: Does this unit require cooling water?
A: The RS-FS-9001 is a dry-type Flame Tracker. The UV-sensitive photodiode is thermally isolated from the hot-end sensor face, allowing operation without external cooling. This is one of the key advantages over older Geiger-Müller tube-based detectors.
A: The RS-FS-9001 is a dry-type Flame Tracker. The UV-sensitive photodiode is thermally isolated from the hot-end sensor face, allowing operation without external cooling. This is one of the key advantages over older Geiger-Müller tube-based detectors.
